Primary side Voltage Fuse Kit 50 - 250 VA, Slow blowing fuse

Secondary side Voltage Fuse Kit 50 - 250 VA, Fast acting fuse

Primary side Voltage Fuse Kit 300 - 500 VA, Slow blowing fuse

Dummy Module

Secondary side Voltage Fuse Kit 750 - 1500 VA, Fast acting fuse

RS422/485 5-point Terminal Block

EZText Enhanced replacement power terminal strip

Spare cover mounts onto 4 module EZPLCs, EZTouch Remote I/O and EZTouchPLCs.  Cover provides protection for base, modules, wiring, etc., while still allowing an operator to view status LEDs and access ports. Includes mounting instruction sheet.

EZText Replacement Ferrite Cores

Programming cable for setup and programming for all EZText Enhanced panels

Spring loaded terminal block for use with EZRack PLC I/O. Includes (2) 10-pin terminal blocks

Screw type terminal block for use with EZRack PLC I/O. Includes (2) 10-pin terminal blocks

Spare cover mounts onto 8 module EZPLCs, EZTouch Remote I/O and EZTouchPLCs. Cover provides protection for base, modules, wiring, etc., while still allowing an operator to view status LEDs and access ports. Includes mounting instruction sheet.

EZ Inductive Proximity Sensor, 18mm Diameter, 10-30VDC, PNP, Nickel Plated Brass, 5.0mm nominal sensing distance, Flush, Normally Open Output, Built-in M12 Connector

To connect any EZTouch & EZText to an AB SLC 5/03, 5/04 or 5/05 CPU with DF-1 port. 15 pin D-shell male connector to 9 pin D-shell female connector.

To connect any EZTouch, EZText or CE Touchpanel to EZPLC. 15 pin D-shell male connector to 9 pin D-shell male connector.

Serial RS232 Programming Cable. You may need a serial to usb converter. Recommend Aten or StarTech.

Replacement 1/2 AA, 3.6 volt lithium battery for EZRack PLC CPU (RTC and Retentive values)

4 point 10-28 VDC (sink/source) Inputs Snap-in I/O; 4 point 10-28 VDC (sink) outputs, 0.5 Amp per point, 1.4 Amp max for 4 outputs.

4 point 10-28 VDC (Sink/Source) Inputs Snap-in I/O; 4 point 10-28 VDC (source) outputs, 0.5 Amp per point, 1 Amp max for 4 DC Outputs.

8 point 10-28 VDC Inputs (sink/source) Snap-in I/O

8 point 10-28 VDC (sink) Outputs Snap-in I/O, 0.5 Amp per point, 1.4 Amp max per module.

8 point 10-28 VDC (source) Outputs Snap-in I/O, 0.5 Amp per point, 1.0 Amp per module.

Coin cell replacement battery for PLC real time clock and back up for user's program in RAM.

To connect any EZTouch, EZText or CE Touchpanel to DL05, DL06, DL105, DL205, D3-350 or D4-450 CPU. 15 pin D-shell male connector to RJ 12 modular connector.

To connect any EZTouch, EZText or CE Touchpanel to a DL06, D2-250(-1) or D2-260 (bottom port) CPU. 15 pin D-shell male connector to 15 pin male HD.

4 point 10-28 VDC (sink/source) Inputs Screw-down I/O; 4 point 10-28 VDC (sink) outputs, 0.5 Amp per point, 1.4 Amp max for 4 outputs.

4 point 10-28 VDC (Sink/Source) Inputs Screw-down I/O; 4 point 10-28 VDC (source) outputs, 0.5 Amp per point, 1 Amp max for 4 DC Outputs.

8 point 10-28 VDC Inputs (sink/source) Screw-down I/O

8 point 10-28 VDC (sink) Outputs Screw-down I/O, 0.5 Amp per point, 1.4 Amp max per module.